LD320 Series High performance driver

project

specifications

IN-OUT

Analog  input

2-way/voltage current signal switchable, voltage 0-10V, current 0-20mA

Digital input

5 channels/optocoupler isolation, including 1 high speed pulse input, with a maximum input pulse frequency of up to 100KHz

analog  output

2 channels/voltage output range 1-10V, current output range 0-20mA, output signal type can be switched

Digital  output

2-way/optocoupler isolation/open collector output/rated current 20mA (DO, HDO)

Digital  pulse output

2 channels/optocoupler isolation/open collector pulse (trequency or PWM) output (DO, HDO),including

1 channel of high-speed pulse output, the maximum output pulse frequency can reach 100KHz

relay  output

2-way/Normally  Open  and  Normally  Closed  Contact/250VAC-3A

communication       mode

Standard  MODBUS-485   communication   protocol

Control

characteristic

control  mode

V/F control; PG free vector control (SVC); With PG vector control

Frequency setting  mode

Multiple setting methods such as keyboard setting, analog quantity setting, pulse setting, communication setting, etc

Frequency control  ange

0.01-500.00Hz

Frequency  control accuracy

Digital setting: 0.01Hz; Analog setting: maximum frequency x 0.025%

speed  range

1:200(SVC);          1:1000(FVC)

Steady  range

±0.5%(SVC);±0.02%(FVC)

Acceleration and deceleration time

1.0-3600.0 seconds (acceleration and deceleration times can be set separately, and S characteristics can be switched)

Inching control

Point frequency range: 0.00Hz-100.00Hz; Point acceleration time: 0.0s-3600s

Starting torque

0.5Hz 150%(SVC) adjustable, considering the capacity of the frequency converter; 3.0Hz 100%(V/F)

Torque  boost

Automatic torque increase; Adjustable manual torque increase of 0.1%-30.0%

braking  torque

Braking resistance braking  (125%), DC braking  (20%)

DC braking

Braking time: 0.0s-36.0s; Braking current: 0.0%-100.0%

timing control

Timing  range:  0.0min-6500min

Pid control

Built in PIO function for convenient closed-loop control of processes

V over F curve

Linear, multi-point custom curve, 1.1-2.0 arbitrary descent curve

Multi stage speed control

Buit-in simple PLC can control the maximum 16 speed frequency logic

Carrier adjustable

Adjustable from 1.0 to 16.0kHz, adjustable according to module temperature

Frequency setting signal

10-+10,0-+10,4-20mA,  high-frequency  pulse,  PWM  pulse

Protection

function

Overload capacity

G:150% 60s 200% 2s ; p:120% 60s 150% 1s

Instantaneous  overcurrent/

short circuit protection

Automatically cut off output when the rated output current exceeds 200%

Overvoltage/secondary voltage protection

When the DC voltage of the bus is too low (360V) or too high (800V), the motor stops freely (except during braking)

Phase loss protection

When there is a phase loss at the input or output end, the motor stops freely

Overheat protection

When the radiator temperature is ≥85 ℃, the motor stops freely; The temperature protection threshold can be freely set according to the ambient temperature

motor protection

Analog input can be connected to temperature sensor inputs (PT100, PT000) to achieve motor overheating protection

Stall protection

Using current sensors to detect stall prevention duning acceleration and daceleraion, and stall prevention during operation (action current can be set)

ground protection

Using current sensors for detection

Instant stop

By compensting for vatlage reducion though load feedback energy, the frequecy conveter can maintain continuous operation for a short petiod of time

Specifications

stucture

Rated  input

voltage:1/3PH     220V±20%;3PH     380V±20%;frequency:50Hz/60Hz±5%

Cooling and protection

≤18.5kW:IP20>18.5kW:1IP10;Forced  air  cooling

Usage   environment

Temp:-10℃-+40℃ altitude: Not higher than 1000m; Indoor, without corrosive gases

Save  Environment

Temp:-20℃-+65℃  humidity:20-90%RH(No  condensation)The  vibration  is  less  than  6m/S  squared(0.6g)